Last Updated on July 23, 2023
Have you ever been in the middle of scrubbing your bathtub, only to realize you’ve run out of cleaner? Desperate for a solution, you might be tempted to grab the nearest bottle of toilet bowl cleaner from under the sink.
The answer to will toilet bowl cleaners hurt fiberglass tubs is no, they won’t hurt. Toilet bowl cleaner is safe to use on fiberglass tubs. It will remove any unwanted layer or substances without damaging the surface of your tub. You can use toilet bowl cleaner on the fiberglass tubs.
There are many ways to clean your tub, and this is one way that you can use it.
Make sure that you read the complete guide on “Will Toilet Bowl Cleaner Hurt Fiberglass Tub” before you use it. This will help you to know how to use it properly.
Will Toilet Bowl Cleaner Hurt Fiberglass Tub: Instructions
Cleaning your fiberglass bathtub with toilet bowl cleaner is one way to clean it, but there are many other ways as well. Be sure to read the directions carefully and understand how to use them properly before you begin. You may also want to try a different type of cleaner.
The process of cleaning a fiberglass bathtub can be quick and easy as long as you have the right tools. Before starting the cleaning process of your fiberglass bathtub, it is important to clear the bathtub of any clutter or items that may be in the way.
- Once the area is clear, spray some toilet bowl cleaner on a cloth or sponge and begin scrubbing the tub in circular motions, paying special attention to areas with soap buildup or algae growth.
- Spray the entire surface of the tub with a toilet bowl cleaner or any fiberglass cleanser, and let it sit for a few minutes.
- Use a nonabrasive scrub brush or sponge to scrub any soap scum or debris from the tub.
- Rinse out the tub with warm water, then wipe it dry with a rag or towel.
- For tougher stains, allow the toilet bowl cleaner to sit on the affected area for longer or even use an additional scrubbing tool, like a pumice stone, before scrubbing again.
- Rinse off the toilet bowl cleaner and wipe down any remaining residue with a clean cloth.
- Use a scrub brush or old toothbrush to get into any small crevices or places that are hard for you to get into.
- Rinse off the entire tub thoroughly and dry it off with a towel before enjoying your sparkling clean bathtub.
By following these steps, your fiberglass bathtub will be sparkling clean.
How to Make Custom Fit Bathtubs from Fiberglass?
Here are various items that you are going to find necessary to have.
- It is necessary to have an A4 size piece of paper and a pencil
- A length measuring tape: The most popular tape measure is 8 feet, but 4 feet is also fine
- A measuring ruler
- A pair of an arc gauge
- An appropriate wooden frame or a PVC plastic frame
- A nail gun with some stainless steel nails or glue that can be used on and bonded to PVC plastic
- A hammer
- Polyurethane foam for making foam molds
- Suitable tools for cutting
- Denatured alcoholic acetone
- Rubber sponge or microfiber sponge
- Protective hand gloves for the protection of your hand
- A protective face mask for the protection of your face
- Several fiberglass sheets
- Resin
- A roller for painting or a spray paint gun
- Paint tray
- An air roller
- A flat bar for prying
- Sander
- Drill
- Suitable tools for cutting bore bits
- A water resistant caulking material
Take time to create a design and craft a fiberglass bathtub. This method relies on principles that are similar to those that are used in crafting any other type of fiberglass construction. It is necessary for the crafter to build a mold for the fiberglass product.
The builder needs first to prepare the fiberglass product in order to begin the process of building the structure gradually. It is a lengthy and complicated process that involves the use of toxic chemicals, which requires special care and precaution in order to prevent injuries.
It is possible for a crafter to produce a bathtub that is made of a specific shape that is very different from the shapes that are available in products that have been designed by commercial suppliers.
Step 1
If you are planning to install a bathtub in a particular room, you should consider the location when it is constructed. Make use of a pencil and a piece of paper to design and clean, and draw out the exact dimensions of the bathtub that you want to build.
Make sure you pay close attention to the angle as well as the diameter of the arcs that are desired. Take a measuring tape, line measure, and an arc measurement gauge and measure out these dimensions on a piece of paper and note the information according to your design.
Step 2
Your design should include dimensions to help you build the fiberglass tub frame. For the sizing skeleton of the mold, connect pieces of wood and PVC pipe using PVC glue or nails and hammers. Make the mold body by inserting the pieces of foam mold into the frame.
Knives and razors are useful cutting tools for cutting foam. Create the inner surface of the mold by shaping the foam. Ensure that the mold shape matches the dimensions of your tub, adding and removing foam as needed.
Step 3
Prepare fiberglass cloth sheets by cutting them with scissors so you can handle them when building the tub. The inner mold surface wall should be cleaned with acetone and a sponge.
Hands should be protected with gloves. Make sure to spray the finished mold with a nonstick wax application in order to separate it from the tub later on. Depending on the situation, buff the inner surface of the wax out.
Step 4
Pour a small amount of fiberglass resin into a mixing bowl and let it settle for a short while before pouring it into an empty paint tray. With the help of a small painting roller, apply the resin inside the mold after dipping it in the tray and spreading it around with the roller.
Once the first layer of resin has been applied, it is necessary to lay a sheet of fiberglass cloth on top of it. When you have flattened the cloth into the resin, you will need to use an air roller. The service area should be covered with cloth sheets in order to ensure a good installation of the first layer.
Make sure that all the first sheets of resin are covered completely. Make sure that the layer is allowed to dry for a few minutes, and then proceed to apply two to three more layers of the same color, depending on how thick the layer is.
After this first phase has been applied to the mold, let it dry for one hour inside the mold. Wait for the resin to harden, and you are done.
Step 5
Continue to apply layers of fiberglass resin and cloth covered with more resin to the tub surface until it reaches the desired thickness of fiberglass resin and cloth coated with more resin on top. It is absolutely essential to ensure that the thickness of the material measures at least 20 millimeters.
Ensure that each layer of paint is smoothed out as it is applied in order to avoid air bubbles from forming in the paint. As the final layer of resin is being applied, let it dry and cure for a few minutes while you finish cleaning up the remaining resin, equipment, and extra cloth after you have applied the final layer of resin.
Step 6
After two days have passed, you can begin the process of separating the cured fiberglass tub. The tub should be separated from the foam with the help of a separator tool, such as a flat prying bar or similar tool.
Remove the tub shell from the fiberglass tub and lay it flat on a work surface. You will need to sand the edges as well as the surface in order for them to be smoothed out in every area. Sharp edges should be removed as necessary.
Step 7
Place the drain and the hardware holes in the fiberglass tub according to their locations. Prepare the cavities and holes by drilling and boring them with a drill bit that will fit your plumbing equipment which is going to be installed inside the bathtub at the end of the hole.
When you are finished, you should sand the edges of the fiberglass tub holes so that they will be clean cuts when they are finished. As soon as the tub has been finished, it should be painted with thick epoxy paint and a surface finisher to ensure that it is ready for use once it has been installed. A clean finish can be achieved by applying multiple coats of paint.
Relevant Article To Read: Is vinegar good for removing carpet paint?
Step 8
Let the painted tub dry for a few hours after it has been painted. When you have built the surrounding tub frame and counters as desired, you can then install the fiberglass tub in its position in the bathroom.
The plumbing hardware should be connected, and the system should be tested to ensure there are no leaks in the tub. A water resistant sealant caulk needs to be applied to the exterior edges of the fiberglass tub to ensure they are securely attached to the surrounding counter frame.
What Else Can You Use Toilet Bowl Cleaner for?
Toilet bowl cleaner is very effective and does an excellent job when it comes to cleaning and getting rid of stains from toilet bowls and leaves a fresh, clean odor in the toilet. The other option is to brush and clean the toilet with a toilet brush. But the toilet cleaner will do most of the work for you.
To clean the toilet bowl, toilet cleaner can also be used for other cleaning tasks around the house. It is great for cleaning sinks, showers, and tubs. You can also use it to clean tile grout and get rid of soap scum.
As a bonus, you can also use the mixture to clean drains in showers and sinks and even clean soap deposits and hair residue from the pipes with the mixture.
Recommended Article To Read: Do Toilet Air Fresheners Last Long?
As a Final Observation
Taking everything into account regarding “will toilet bowl cleaner hurt fiberglass tub” cleaning a fiberglass tub using a toilet bowl cleaner is not a complicated task, but it does require some patience and attention to detail. If you follow the instructions above carefully, you should have no trouble creating a beautiful and functional bathtub for your home.
If there is any question about the use of toilet bowl cleaner on fiberglass tubs, it is best to test an inconspicuous area before full application. If there is any damage or discoloration to the fiberglass after testing, discontinue use and seek professional help.